20 Best Two Post Lift (2022 Updated)

Please compare with others before you make the decision. Check layout dimension against floor plan requirements making sure adequate space is available. Your lift requires a 220v, 30amp, single phase, grounded electrical source.

There should be room enough to operate the lift in a safe manner and without restrictions. – Overhead Area: The area where the lift will be located should be free of overhead obstructions such as heaters, building supports, electrical lines, doors, lights, etc.

– Floor Area: Visually inspect the site where the lift is to be installed and check for cracked or defective concrete. Floor Requirements – A level floor is suggested for proper installation and level lifting.

Small differences in floor slopes may be compensated for by proper shimming. If a floor is of questionable slope, consider a survey of the site and/or the possibility of pouring a new level concrete slab.

– New concrete must be adequately cured for at least 30 days. DO NOT install auto lift on any asphalt surface or any surface other than concrete. DO NOT install auto lift on expansion seams or on cracked or defective concrete.

DO NOT install auto lift on a second/elevated floor without first consulting building architect. DO NOT install auto lift outdoors unless special consideration has been made to protect the power unit from inclement weather conditions.

Concrete Specifications All models MUST be installed on 3,000 PSI reinforced concrete only. Additional concrete requirements will vary by lift. 8,500 lbs – 10,000 lbs lifts: 4′′ Minimum Thickness 11,000 lbs – 15,000 lbs lifts: 6′′ Minimum Thickness.

Please compare with others before you make the decision. Check layout dimension against floor plan requirements making sure adequate space is available. Your lift requires a 220v, 30amp, single phase, grounded electrical source.

There should be room enough to operate the lift in a safe manner and without restrictions. – Overhead Area: The area where the lift will be located should be free of overhead obstructions such as heaters, building supports, electrical lines, doors, lights, etc.

– Floor Area: Visually inspect the site where the lift is to be installed and check for cracked or defective concrete. Floor Requirements – A level floor is suggested for proper installation and level lifting.

Small differences in floor slopes may be compensated for by proper shimming. If a floor is of questionable slope, consider a survey of the site and/or the possibility of pouring a new level concrete slab.

– New concrete must be adequately cured for at least 30 days. DO NOT install auto lift on any asphalt surface or any surface other than concrete. DO NOT install auto lift on expansion seams or on cracked or defective concrete.

DO NOT install auto lift on a second/elevated floor without first consulting building architect. DO NOT install auto lift outdoors unless special consideration has been made to protect the power unit from inclement weather conditions.

Concrete Specifications All models MUST be installed on 3,000 PSI reinforced concrete only. Additional concrete requirements will vary by lift. 8,500 lbs – 10,000 lbs lifts: 4′′ Minimum Thickness 11,000 lbs – 15,000 lbs lifts: 6′′ Minimum Thickness.

Single Point Safety Lock Release System Combo (Symmetrical and Asymmetrical) Arm Assembly with Screw-in Pads! CE Certified Lift Structure and Hydraulic System 6’9″ Lift Height Maximum with Truck Adapters All Robot Welded Structure with Durable Powder Coated Finish Double Seal Rings Protecting PU Material Carriage Material Q355 (ASTM A572), Stronger Than Normal Q235 Steel APlusLift AP-10SR car lift (auto hoist) is one of the most affordable single release over head car lifts built with quality materials and good workmanship.

It is an upgrade from the bestselling HW-10KOH-A model with an addition of single point lock release. (No need to walk to the other column to release the locks!) The lift has a strong double “S” column design to support 10,000 LB capacity.

Residential address has $50 additional charge. No liftgate service as the car lift package is too long. Please prepare your own unloading equipment (like a forklift, bobcat, cherrypicker, or flatbed truck) to unload.

Self Pickup Locations with Discount: Ontario (OH) and Watsontown (PA).

Every XPR-10AS features Direct-Drive technology that’s only available with BendPak. The asymmetrical design of this lift has rotated columns, which makes it easier to enter and exit the vehicle and reduces the chance of door dings.

Professionals love the power and reliability of the lift, and they know our reputation precedes us. Meanwhile, DIY’ers with high ceilings know BendPak means safe lifting in the comfort of home. Skip the headache of an uncertified, poorly welded piece of garbage and trust our best to lift your best.

The XPR-10S two-post lift offers exceptional direct-drive lifting performance. This industrial-strength car lift guarantees cutting-edge technology, top of the line materials, a design that’s ahead of its time and a 10,000-lb.

lifting capacity. All height/width variations fit in shops with ceilings higher than 12’, and none of them will crowd your floor while you work beneath a vehicle. Every XPR-10S two-post lift features our telescoping screw pad assembly kit.

Finding the lift points on bigger trucks and vehicles with a two-post lift can often be a challenging procedure. When lift arms are too short, they need to be moved closer together to reach the vehicle lift points and this makes it hard to find the vehicle’s center of balance on especially long wheelbases.

But the new BendPak XPR-12CL-LTA solves this problem and allows you to reach even the longest, most difficult wheelbases in the industry. The XPR-12CL-LTA features three-stage telescoping lift arms with a 72” maximum range, extending even further than the 58” on our standard XPR- 12CL two-post lift series.

This broader option allows you to find the center of balance on the biggest trucks around, giving you the versatility and power to safely lift any vehicle up to its 12,000-lb. capacity. Features Dimension-151x29x43 CE Approved and Certified.

The 2post BendPak SuperDuty Truck Lift is designed for fullsize truck service. The lift delivers clearfloor convenience a fast lift speed and less maintenance for improved efficiency and productivity.

Taller people know that the difference between stooping and standing under a two-post lift can be the difference between severe back/neck pain and working in total comfort.

If you appreciate the superior quality of a BendPak XPR-9 or 10 series two-post lift but need more lifting power, the XPR-12FDL is an open-top car lift thats packed with pure, brutish muscle. Like its Clearfloor sister-lift, it offers superior Direct-Drive performance.

The XPR-12FDL is the perfect lifting application for everything that falls in its weight class. Two robust posts are capable of raising some truly massive trucks and SUVs. This might be classified as our medium-duty lift, as it covers almost every vehicle in the homeowner/residential arena.

It might be the most versatile lift you ever own, given that its low-profile arms will easily reach the lift points of low-stance race cars and sports cars (including both foreign and domestic models).

The columns are set wide to fit trucks and SUVs, but the dual triple-telescoping arms reach farther than the arms on our lighter-duty lifts. With the XPR-12FDL, youre not sacrificing the ability to service smaller vehicles as you gain the ability to service large ones.

The XPR-12FDL is an open-top design. An open-top lift does not have a crossbar over the top of the lift, which is desirable for taller vehicles. The hydraulic lines run on the floor, under a floorplate, between the posts.

Our XPR-10AS asymmetric 2 post lift offers the convenience of wide or narrow installation wrapped up into one configurable package. This durable, safe, and reliable car lift features an expandable top beam and Tru-Metric arms to suit virtually every vehicle lifting requirement.

The simple, yet highly sophisticated lift design keeps service and maintenance costs to a minimum, delivering lower operating expenses and higher productivity.

Just because the BendPak XPR-12FDL super-duty model was designed for the big stuff doesn’t mean it can’t handle your light-duty work as well. The two post car hoist XPR-12FD easily has the capacity to lift your largest full-sized pickups and commercial vehicles, yet still provide specific capability for sport and compact cars, both foreign and domestic.

The 2 post car hoist XPR-12FD is a 12,000-lb. maximum capacity, close-top model hoist with full-reach arms that collapse to standard lengths and lower hoist pads that clutch standard passenger automobiles, yet still hold the big guys as well.

The columns are also placed wider for trucks with fixed towing mirrors. Sound complicated to operate? Don’t worry. When it comes to ease of use, our dual-synchro equalization system and user-friendly controls are the stuff of legends.

Taller people know that the difference between stooping and standing under a two-post lift can be the difference between severe back/neck pain and working in total comfort.

Specifically, the powerful and secure super-duty XPR-12FDL is an incredibly rapid car hoist with a robust menu of features to increase efficiency and productivity, without overwhelming you with serviceable parts and necessary maintenance.

The results are lower operating expenses and higher productivity.

Our XPR-10AS asymmetric two-post lift offers the convenience of wide or narrow installation wrapped up into one configurable package. This durable, safe and reliable car lift features an expandable top beam and Tru-Metric arms to suit virtually every vehicle lifting requirement.

The powerful and secure XPR-10AS is an incredibly rapid lift with a robust menu of features to increase efficiency and productivity. A simple, yet highly sophisticated lift design keeps service and maintenance costs to a minimum, delivering lower operating expenses and higher productivity.

Every XPR-12CL two-post lift is designed to keep your floor clean. Our Clearfloor design offers enough space for cars and trucks up to 12,000 lbs. This is an incredibly rapid lift with robust menus of features to increase efficiency and productivity.

They never overwhelm you with serviceable parts and constant maintenance, and as a result, you get lower operating expenses and higher productivity. The XPR-12CL two-post lift can easily raise your largest full-sized pickups and commercial vehicles, yet they still provide specific capability for sport and compact cars, both foreign and domestic.

The 12K capacity features full-reach arms that collapse to standard lengths and lower-seating lift pads that clutch standard passenger automobiles. When it comes to ease-of-use, our dual-synchro equalization system and user-friendly controls are legendary.

The XPR-12CL is our closed-top model. A closed-top model offers clearfloor convenience, as it runs hydraulic lines up and out of sight, but it may not fit taller vehicles. A closed-top/clearfloor two-post lift allows two technicians to easily move toolboxes, transmission jacks, oil drains and other equipment underneath the elevated vehicle.

Load Capacity The Bendpak 10,000-lb. 2-Post Wide Clearfloor Asymmetric Lift – XPR-10AS is a direct drive lift that provides a drive-thru clearance. The posts are rotated 30o inwards to give you the ability to open doors while a vehicle is raised.

This lift will fit in shops that have a ceiling height higher than 12 feet. This lift is built with low-pressure HVLP dual direct drive cylinders. This true asymmetric lift features 30° rotated columns for added door-opening clearance and interior car access.

The exclusive Tru-Metric carriage and arm design combines to give users the ability to load vehicles either symmetrically (centerline of vehicle at column) or asymmetrically (centerline of vehicle behind column).

Bendpak XPR-10AS easily has the capacity to lift some of your largest full-sized pickups and commercial vehicles, yet still provide specific capability for sport and compact cars, both foreign and domestic—the two-post car lift is a rugged, close-top model unit with a 10,000-lb.

maximum capacity. This clearfloor model provide unobstructed floor space allowing technicians to easily move toolboxes, transmission jacks, oil drains and other equipment underneath the elevated vehicle.

Key Features of the Bendpak 10,000-lb. Technical Specifications* Lifting Capacity: 10,000 lbs. Overall Height: 145″ Overall Width (Narrow): 137″ Overall Width (Wide): 145″ Outside Columns (Narrow): 133″ Outside Columns (Wide): 141″ Floor to Overhead Switch: 141″ Inside Columns (Narrow): 104″ Inside Columns (Wide): 112″ Front Arm Min.

Reach: 23-1/2″ Front Arm Max. Reach: 45-1/2″ Rear Arm Min. Reach: 42-1/2″ Rear Arm Max. Reach: 60″ Min. Pad Height: 4. 25″ – 6. 75″ Rise: 69″ Lift Height Max (Pad Only): 73-75″ Lift Height Max (3″ Adapter): 75.

5-77. 5″ Drive-Thru Clearance (Narrow): 94″ Drive-Thru Clearance (Wide): 102″ Screw Pad Adjustment: 2″ Motor: 220 VAC / 60 Hz / 1 Ph Time to Full Rise: 45 seconds Max Load per Arm: 2,500 lbs. *The design, material, and specifications are subject to change without notice.

$100 Limited Access Fee for deliveries to schools.

The powerful and secure super-duty XPR-12C is an incredibly rapid lift with a robust menu of features to increase efficiency and productivity, without overwhelming you with serviceable parts and necessary maintenance.

The results are lower operating expenses and higher productivity.

The safe and rugged XPR-12CL-192 2-Post lift features extended height columns for added overhead clearance and an adjustable top beam to accommodate wide or narrow installation set-ups. The highly sophisticated yet simple and dependable XPR-Series design requires very little service or maintenance for an overall lower cost of ownership.

All BendPak’s XPR 2-Post models feature dual “direct-drive” low-pressure cylinders, maintenance-free UHMW load bearings, single-piece columns, extra-tall lifting carriages and triple-telescoping arm configurations for increased arm positioning versatility.

Revolutionary 30deg rotated column offers added door-opening clearance and interior car access Exclusive Tru‐Metric carriage and arm design combines to give users the ability to load vehicles either symmetrically (centerline of vehicle at column) or asymmetrically (centerline of vehicle behind column) – it’s almost like having two lifts in one Expandable top beam accommodates wide or narrow drive-thru configuration Padded overhead safety shutoff bar Single-point safety release This BendPak asymmetric two-post lift offers the convenience of wide or narrow installation wrapped up into one configurable package.

The durable, safe and reliable car lift features an expandable top beam and Tru-Metric arms to suit virtually every vehicle-lifting requirement. The powerful and secure XPR-10A is an incredibly rapid lift with a robust menu of features to increase efficiency and productivity.

It’s a simple yet highly sophisticated lift designed to minimize service and maintenance costs while delivering low operating expenses and high productivity. Lift Capacity (lbs. ): 10,000, Max. Rise (in.

): 69, Time of Full Rise (seconds): 45, Overall Width (in. ): 132-145, Pad Height (in. ): 4, Drive-Thru Clearance (in. ): Narrow configuration: 80; Wide configuration: 102, Overall Height (in. ): 145, Motor Phase(s): 1, Volts: 220, HP: 2.

Rugged enough for full-size trucks – low enough for sports cars. Our XPR-10AS-LP asymmetric two-post lift features our exclusive Low-Pro arms that better accommodate lowered sports cars and vehicles with ground effects.

This durable, safe, and reliable car lift features an expandable top beam for wide or narrow installation and Tru-Metric arms to suit virtually every vehicle lifting requirement. The simple, yet highly sophisticated lift design keeps service and maintenance costs to a minimum, delivering lower operating expenses and higher productivity.